Non usb connection hp printer 940c hook up

#NON USB CONNECTION HP PRINTER 940C HOOK UP HOW TO#
#NON USB CONNECTION HP PRINTER 940C HOOK UP DRIVERS#

Use same technique as in the step 12.STEP 16.Carefully separate the top cover from the laptop base.Continue removing cover with your fingers.STEP 17.The top cover has been removed.HereвЂ™s the opposite side of the top cover.Here you can access and remove (if needed) the finger scanner and power button board.STEP 18.Disconnect display video cable from the motherboard.Pull both wireless antenna cables through the hole in the bottom cover.STEP 19.Remove four screws securing display hinges.STEP 20.Now you can separate the display panel from the base.The display panel is ready for the LCD screen replacement.HereвЂ™s the laptop base with the display panel removed.In a HP Pavilion dm4 laptop the DC power jack is not soldered to the motherboard. Do not separate the locking tab from the white base.On the following picture the keyboard connector shown in the unlocked position.STEP 13.Now you can pull keyboard cable from the connector and remove the keyboard.STEP 14.Remove all screws from the bottom of the laptop.There are two screws hidden under base feet (green circles).Remove the rubber foot with a sharp object and remove the screw.STEP 15.Remove four screws securing the top cover.Disconnect three cables.

рџ™‚STEP 9.Continue separating the keyboard from the top cover.STEP 10.Finally, lift up the top side of the keyboard and flip it upside down on the palm rest.STEP 11.Now you can access the keyboard cable and disconnect it from the motherboard.STEP 12.The keyboard connector opens up as it shown on the picture below.Carefully open the brown tab at a 90 degree angle. IвЂ™m using a thin plastic tool for that.After the keyboard separates from the top cover you can continue removing it with your fingers.To make it more complicated, HP glued the keyboard to the top cover with double sticky tape. There is no way you can do it from the top without damaging the keyboard.HereвЂ™s how I did it.In the DVD drive compartment there is a hole and you can use it for removing the keyboard.Very carefully push the keyboard through the hole in the DVD drive compartment. Remove the cover.STEP 3.When all covers removed youвЂ™ll be able to access both memory modules, hard drive, CMOS battery and wireless card.For the purpose of my guide itвЂ™s not necessary to remove memory modules, wireless card and CMOS battery.STEP 4.Disconnect hard drive cable from the motherboard.Remove the hard drive assembly.STEP 5.Carefully disconnect both antenna cables from the wireless card.Again, weвЂ™ll leave the wireless card connected to the motherboard.STEP 6.Remove one screw securing the DVD drive.Slide DVD drive to the left and remove it.STEP 7.Remove two screws securing the keyboard.STEP 8.ItвЂ™s very tricky removing the keyboard from a HP Pavilion dm4 laptop.

#NON USB CONNECTION HP PRINTER 940C HOOK UP HOW TO#

Unfortunately, in order to replace it in an HP Pavilion dm4, itвЂ™s necessary to remove the display panel first.IвЂ™ll split disassembly instructions in two posts.In this post I explain how to remove the display panel and in the next one IвЂ™ll explain how to replace the screen.Before you start make sure the computer is turned off and battery removed.STEP 1.Remove two screws securing the memory cover in battery compartment.STEP 2.Slide and remove the memory cover.Remove two screws securing the hard drive cover. Compaq & HP | 158 In this guide I explain how to disassemble a HP Pavilion dm4 laptop.IвЂ™m doing this disassembly in order to replace damaged screen. After the cable is installed it may take about two minutes for the files to be copied and the Next button to become available.By IML Tech | posted in: 3.

#NON USB CONNECTION HP PRINTER 940C HOOK UP DRIVERS#

With an existing computer, complete the setup by following steps 11 and 12ДЎ1)Insert the Drivers and Utilities CD, and follow the instructions on your screen.ДЎ2)Connect the USB cable (sold separately), when prompted with drivers, between the printer and the computer.With a new Dell computer, complete the setup by following step 12.Insert the ink cartridges (black or photo on the left and color on the right).Remove the tape from the two ink cartridges.The ink cartridge carrier moves to the center. Press the Select button to save the selection. Use the arrow buttons to find the display language and the paper size.Connect the power cable to the printer and then to the wall, and press the Power button.Insert the paper, center the paper on the paper support, and then adjust the paper guides.Raise the paper support, and extend the paper tray.Unpack your printer, and remove all tape and packaging material from the printer.

Non usb connection hp printer 940c hook up